|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Current Limited Load Switch General Description The AAT4610 SmartSwitch is a current limited Pchannel MOSFET power switch designed for highside load switching applications. This switch operates with inputs ranging from 2.7V to 5.5V, making it ideal for both 3V and 5V systems. An integrated current-limiting circuit protects the input supply against large currents which may cause the supply to fall out of regulation. The AAT4610 is also protected from thermal overload which limits power dissipation and junction temperatures. It can be used to control loads that require up to 1A. Current limit threshold is programmed with a resistor from SET to ground. The quiescent supply current is typically a low 15A max. In shutdown mode, the supply current decreases to less than 1A. The AAT4610 is available in a Pb-free 5-pin SOT23 package and is specified over the -40C to +85C temperature range. AAT4610 Features * * * * * * * * * * * * SmartSwitchTM Typical Application NO T FO R R EC NE O M WM DE EN SI DE G NS D Applications * * * * Hot Swap Supplies Notebook Computers Peripheral Ports Personal Communication Devices UL Recognized Component INPUT IN OUTPUT OUT Input Voltage Range: 2.7V to 5.5V Programmable Over-Current Threshold Fast Transient Response: -- <1s Response to Short Circuit Low Quiescent Current -- 15A Typical -- 1A Max with Switch Off 160m Typical RDS(ON) Only 2.5V Needed for ON/OFF Control Under-Voltage Lockout Thermal Shutdown 4kV ESD Rating UL Approved--File No. E217765 5-Pin SOT23 Package Temperature Range: -40C to +85C AAT4610 GND ON (ON) ON/(ON) SET 1F RSET 0.47F GND GND 4610.2006.09.1.3 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 1 Current Limited Load Switch Pin Descriptions Pin # 1 2 3 4 5 AAT4610 Symbol OUT GND SET ON IN Function P-channel MOSFET drain. Connect 0.47F capacitor from OUT to GND. Ground connection Current limit set input. A resistor from SET to ground sets the current limit for the switch. Enable input. Two versions are available, active-high and active-low. See Ordering Information for details. P-channel MOSFET source. Connect 1F capacitor from IN to GND. Pin Configuration SOT23-5 (Top View) OUT GND SET 1 5 IN 2 3 4 ON 2 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 4610.2006.09.1.3 Current Limited Load Switch Absolute Maximum Ratings1 TA = 25C, unless otherwise noted. Symbol VIN VON VSET, VOUT IMAX TJ TLEAD VESD AAT4610 Description IN to GND ON (ON) to GND SET, OUT to GND Maximum Continuous Switch Current Operating Junction Temperature Range Maximum Soldering Temperature (at leads) ESD Rating2 - HBM Value -0.3 to 6 -0.3 to VIN + 0.3 -0.3 to VIN + 0.3 2 -40 to 150 300 4000 Units V V V A C C V Thermal Characteristics3 Symbol JA PD Description Thermal Resistance Power Dissipation Value 150 667 Units C/W mW 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. 3. Mounted on a demo board. 4610.2006.09.1.3 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 3 Current Limited Load Switch Electrical Characteristics VIN = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C. Symbol VIN IQ IQ(OFF) ISD(OFF) VUVLO RDS(ON) ILIM ILIM(MIN) VON(L) VON(H) ION(SINK) TRESP TOFF TON TSD AAT4610 Description Operation Voltage Quiescent Current Off Supply Current Off Switch Current Under-Voltage Lockout On Resistance Current Limit Minimum Current Limit ON (ON) Input Low Voltage ON (ON) Input High Voltage ON (ON) Input leakage Current Limit Response Time Turn-Off Time Turn-On Time Over-Temperature Threshold Conditions VIN = 5V, ON (ON) = Active, IOUT = 0 ON (ON) = Inactive, VIN = 5.5V ON (ON) = Inactive, VIN = 5.5V, VOUT = 0 Rising Edge, 1% Hysteresis VIN = 5.0V VIN = 4.5V VIN = 3.0V RSET = 6.8k Min 2.7 Typ 15 0.03 2.3 160 165 195 1 150 Max Units 5.5 30 1 15 2.7 180 230 1.25 0.8 V A A A V m A mA V V 2.0 0.75 VIN = 2.7V to 3.6V VIN = 4.5V to 5.5V VON = 5.5V VIN = 5V VIN = 5V, RL = 10 VIN = 5V, RL = 10 TJ Increasing VIN = 5V TJ Decreasing 2.0 2.4 0.01 0.8 0.4 40 125 115 1 2 200 A s s s C 4 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 4610.2006.09.1.3 Current Limited Load Switch Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. AAT4610 Quiescent Current vs. Temperature Quiescent Current (A) 25 20 15 10 5 0 -40 -20 0 20 40 60 80 100 120 Quiescent Current vs. Input Voltage 40 Input Current (A) 30 20 10 0 2.5 3 3.5 4 4.5 5 5.5 Temperature (C) Input Voltage (V) Output Current vs. Output Voltage (RSET = 16k) 0.6 RDS(ON) vs. Temperature 250 200 Input = 3V Input = 5V Output Current (A) 0.4 RDS(ON) (m) 150 100 50 0 -40 -20 0 20 40 0.2 0 0 1 2 3 4 5 60 80 100 Output Voltage (V) Temperature (C) Off-Supply Current vs. Temperature Off-Supply Current (A) 10 10 Off-Switch Current vs. Temperature Off-Switch Current (A) 1 1 0.1 0.1 0.01 0.01 -40 -20 0 20 40 60 80 100 120 0.001 -40 -20 0 20 40 60 80 100 120 Temperature (C) Temperature (C) 4610.2006.09.1.3 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 5 Current Limited Load Switch Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. AAT4610 Turn-On Time vs. Temperature 80 0.45 0.4 Turn-Off Time vs. Temperature Turn-On Time (s) Turn-Off Time (s) 70 60 50 40 30 20 10 0 - 40 - 20 0 20 40 60 80 100 VIN = 3V 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 - 40 VIN = 3V VIN = 5V VIN = 5V - 20 0 20 40 60 80 100 Temperature (C) Temperature (C) Turn On (RL = 10; CL = 0.47F; IOUT = ILIMIT) 6 5 4 Turn Off (RL = 10; IOUT = ILIMIT) 6 5 ON Output Voltage (V) 4 3 2 1 0 -1 - 0.5 Voltage (V) 3 2 1 0 -1 - 20 ON Output 0 20 40 60 0 0.5 1 Time (s) Time (s) Short-Circuit Through 0.3 Input and Output Voltage (V) 8 12 Short-Circuit Through 0.6 Input and Output Voltage (V) 8 9 Output Current (A) Output Current (A) 6 Input Voltage Output Current 8 6 Input Voltage 6 4 4 4 3 Output Current 2 0 2 0 Output Voltage 0 0 1 2 3 -4 Output Voltage 0 0 1 2 3 -3 Time (s) Time (s) 6 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 4610.2006.09.1.3 Current Limited Load Switch Typical Characteristics Unless otherwise noted, VIN = 5V, TA = 25C. AAT4610 RSET vs. ILIM 100 10 RSET Coefficient vs. ILIM RSET ILIM Product (kV) 1 10 9 8 7 6 5 0 0.5 1 1.5 2 RSET (k) 10 1 0.1 ILIM (A) ILIM (A) Current Limit vs. Temperature (RSET = 22.1k; VIN - VOUT = 0.5V) 6 4 2 0 -2 -4 -6 -50 - 25 0 25 50 75 100 Current Limit (%) Temperature (C) 4610.2006.09.1.3 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 7 Current Limited Load Switch Functional Block Diagram AAT4610 IN OUT UnderVoltage Lockout Over-Temperature Protection ON (ON) 1.2V Reference Current Limit SET RSET GND Applications Information Setting Current Limit In most applications, the variation in ILIM must be taken into account when determining RSET. The ILIM variation is due to processing variations from part to part, as well as variations in the voltages at IN (Pin 5) and OUT (Pin 1), plus the operating temperature. See the charts "Current Limit vs. Temperature" and "Output Current vs. VOUT" in the Typical Characteristics section of this datasheet. Together, these three factors add up to a 25% tolerance (see ILIM specification in the Electrical Characteristics section of this datasheet). Figure 1 shows a cold device with a statistically higher current limit, and a hot device with a statistically lower current limit, both with RSET equal to 10.5k. While the chart, "RSET vs. ILIM" indicates an ILIM of 0.7A with an RSET of 10.5k, this figure shows that the actual current limit will be at least 0.525A, and no greater than 0.880A. I LIM (A) 1.2 1 0.88A Device with high current limit at -40C 0.8 0.6 0.4 0.525A Device with low current limit at 85C 0.2 0 0 1 2 3 4 5 VOUT (V) Figure 1: Output Current Using 10.5k. To determine RSET, start with the maximum current drawn by the load, and multiply it by 1.33 (typical_ILIM = minimum_ILIM / 0.75). This is the typical current limit value. Next, refer to "RSET vs. ILIM" and find the RSET that corresponds to the typical current limit value. Choose the largest resistor available that is less than or equal to it. For greater precision, 8 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 4610.2006.09.1.3 Current Limited Load Switch the value of RSET may also be calculated using the ILIM RSET product found in the chart "RSET Coefficient vs. ILIM". The maximum current is derived by multiplying the typical current for the chosen RSET in the chart by 1.25. A few standard resistor values are listed in Table 1. Device Will Device Always Current Not Current Current Limits RSET Limit Limit Below Below (k) Typ (mA) (mA) (mA) 40.2 30.9 24.9 22.1 19.6 17.8 16.2 14.7 13.0 10.5 8.87 7.50 6.81 6.04 5.49 4.99 4.64 200 250 300 350 400 450 500 550 600 700 800 900 1000 1100 1200 1300 1400 150 188 225 263 300 338 375 413 450 525 600 675 750 825 900 975 1050 250 313 375 438 500 563 625 688 750 875 1000 1125 1250 1375 1500 1625 1750 AAT4610 imately 0.700A as a typical ILIM value for 10.5k. Multiplying 0.700A by 0.75 and 1.25 shows that the AAT4610 will limit the load current to greater than 0.525A but less than 0.875A. Operation in Current Limit When a heavy load is applied to the output of the AAT4610, the load current is limited to the value of ILIM determined by RSET (see Figure 2). Since the load is demanding more current than ILIM, the voltage at the output drops. This causes the AAT4610 to dissipate a larger than normal quantity of power, and results in increased die temperature. When the die temperature exceeds an over-temperature limit, the AAT4610 will shut down until is has cooled sufficiently, at which point it will start up again. The AAT4610 will continue to cycle on and off until the load is removed, power is removed, or until a logic high level is applied to ON (Pin 4). Enable Input In many systems, power planes are controlled by integrated circuits which run at lower voltages than the power plane itself. The enable input ON (Pin 4) of the AAT4610 has low and high threshold voltages that accommodate this condition. The threshold voltages are compatible with 5V TTL and 2.5V to 5V CMOS. Table 1: Current Limit RSET Values. Example: A USB port requires 0.5A. 0.5A multiplied by 1.33 is 0.665A. From the chart "RSET vs. ILIM," RSET should be less than 11k. 10.5 k is a standard value that is a little less than 11k. The chart gives approx- Reverse Voltage The AAT4610 is designed to control current flowing from IN to OUT. If a voltage is applied to OUT which is greater than the voltage on IN, large currents may flow. This could damage the AAT4610. 1 0.75 Output Voltage (V) 0.5 0.25 0 5 4 3 2 1 0 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 Output Current (A) Output Current 1 load is turned on at time = 0 Output Voltage Figure 2: Overload Operation. 4610.2006.09.1.3 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 9 Current Limited Load Switch Ordering Information Package SOT23-5 SOT23-5 AAT4610 Enable ON (active low) ON (active high) Marking1 AAXYY AWXYY Part Number (Tape and Reel)2 AAT4610IGV-T1 AAT4610IGV-1-T1 All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. Package Information SOT23-5 2.85 0.15 1.90 BSC 0.95 BSC 1.575 0.125 1.10 0.20 0.60 REF 2.80 0.20 1.20 0.25 0.15 0.07 4 4 GAUGE PLANE 10 5 0.40 0.10 0.075 0.075 0.60 REF 0.45 0.15 0.10 BSC All dimensions in millimeters 1. XYY = assembly and date code. 2. Sample stock is generally held on all part numbers listed in BOLD. (c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 10 Not recommended for new designs; pin-for-pin upgrade: AAT4610A. 4610.2006.09.1.3 |
Price & Availability of AAT4610IGV-T1 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |